A Beginner's Guide to Installing a Bathtub
A Beginner's Guide to Installing a Bathtub
Blog Article
The content listed below involving How to Install a Bathtub is pretty much motivating. Read it for yourself and decide what you think of it.
Setting up a bathtub isn't specifically rocket science, however it does require solid plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bath tub with a new one is also a reasonably difficult job. If the old tub is easily accessible, the job can relocate rapidly; if you need to open a wall to get rid of the old tub as well as place the brand-new bathtub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will certainly need a helper to leave the old bathtub and also embeded in the brand-new one. Make sure you have qualified yourself for the task as well as fit trying it. As opposed to working with a contractor to take over a halfway-completed job, it is better to consider utilizing one prior to you begin. Opportunities are you may require an expert plumber to make tube connections.
This write-up will aid you set up a brand-new tub in your bathroom if you have actually currently gotten a brand-new tub and do not require to transform the arrangement of your previous water pipelines.
Your tools and product list ought to consist of the following:
Planning for the Installment
Firstly, the sustaining frame supplied with the bath ought to be fitted (if needed) according to the manufacturer's directions. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is essential to see to it that if the tap comes with a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bath, it is likewise practical to fit a supporting plate under the taps system to avoid stress on the tub.
Fit the versatile faucet ports to the bottom of both taps utilizing 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Make certain you use every one of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bath ought to currently prepare to be suited its last placement.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installation, then the first thing you ought to do is disconnect the water. After doing so, activate the taps to drain pipes any type of water remaining in the system. The procedure of eliminating the existing faucets can be rather problematic as a result of the limited accessibility that is frequently the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the taps. Have a cloth ready for the remaining water that will certainly originate from the pipelines. When the supply pipes have been gotten rid of, make use of the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from turning during this procedure. As soon as the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any type of old securing substance.
Prior to proceeding to fit the brand-new faucets, contrast the pipe links on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.
Installing the Bathtub
Using the two wooden boards under its feet, place the bathtub in the called for placement. The wood boards are helpful in equally spreading out the weight of the bath tub over the area of the boards instead of focusing all the weight onto 4 tiny points.
The next goal is to make sure that the bath tub is leveled all round. This can be attained by checking the spirit level and changing the feet on the tub up until the level reviews degree.
To install taps, fit the bottom of the furthest flexible tap connector to the appropriate supply pipe by making a compression sign up with; after that do the exact same for the various other tap.
Switch on the water as well as inspect all joints as well as new pipework for leaks and also tighten them if required. Load the bathtub as well as additionally examine the overflow electrical outlet as well as the typical outlet for leakages.
Finally, repair the bathroom paneling as described in the manufacturer's instruction manual. Tiling as well as sealing around the bathtub ought to wait until the bathtub has been used at least when as this will certainly resolve it into its final placement.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic connector to stop damage to the string. One end of the port fits on the plastic tail of the faucet and also the other end provides a link to the current supply pipelines.
If you need to fit a monobloc, then you will certainly call for reducing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, position the tap in the installing hole in the bath/basin making sure that the washing machines remain in area in between the faucet and also the sink. Safeguard the faucet in place with the supplier given backnut. As soon as the faucet is firmly in place, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with normal faucet adapters. The previous type should be attached to the faucet ends initially, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the location where the bathroom satisfies the tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the fitting can relocate enough to fracture a rigid seal, creating the water to permeate the wall surface between the bath and also the tiling, resulting in difficulties with dampness as well as feasible leakages to the ceiling below.
You can pick from a selection of coloured sealants to blend in your components and fittings. They are offered in tubes and also cartridges, and also are capable of sealing spaces as much as a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly load the bath tub with water prior to securing, to allow for the motion experienced when the bathtub is in usage. The sealer can crack fairly early if you do not think about this activity prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally quickly available on the marketplace. It is suggested to fit the ceramic tiles using waterproof or water resistant adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was shown that article on A Step-by-Step Guide to Installing a Bathtub from a good friend on our other domain. Feel free to set aside a second to distribute this entry if you liked it. Thank-you for going through it.
Got trouble? Ring! Report this page